Q&A - AIRODEK

Can the AIRODEK slab formwork be hired?

Yes. Altrad Coffrage & Etaiement offers AIRODEK for sale as well as for hire.

What is the Quick-strip option of the AIRODEK formwork system?

The Quick-strip is an option within the AIRODEK system from Altrad Formwork & Shoring that enables panels to be removed quickly. The equipment can be reused sooner on subsequent sections, which increases the formwork turnover rate and reduces the number of panels required on site.

What panel sizes are available with the AIRODEK system?

The AIRODEK range offers panels ranging from 900 x 300 mm up to 1800 x 900 mm. This modular design makes it possible to cover standard floor grid patterns and to deal with edges and compensation zones, whilst the clamps allow up to four panels to be positioned securely.

Q&A - ALTRAGRILLE

What is Altragrille?

Altragrille is a construction site guardrail system offered by Altrad Coffrage & Étaiement. It comprises a reversible post, 1.10 m high panels and suitable bases. It complies with the NF EN 13374 standard and features an anti-disengagement system that secures the panel should it be lifted.

What sizes of grilles are available from Altragrille?

Three sizes: 1.20 × 1.10 m (ref. 413-0120A, 5.7 kg), 2.20 × 1.10 m (ref. 413-0220A, 10 kg) and 2.50 × 1.10 m (ref. 413-0250A, 12.1 kg). The standard centre-to-centre spacing of the posts is 1,000, 2,000 and 2,300 mm.

How do you fit an Altragrille grating?

Insert the post into its base and lock it in place by turning it 22.5° anti-clockwise. Then place the grid on top, with the empty side facing up, slide the slider under the tab and secure the lowest horizontal wire. To dismantle, follow the steps in reverse order.

Can the Altragrille post be used without a base?

Yes. The reversible post can be used without a base, with the top facing downwards.

Q&A - ALTRADAL

Which slab formwork should you choose to reduce the physical strain on site?

Altrad’s ALTRADAL aluminium slab formwork is designed to minimise physical strain: its aluminium beams and panels are lightweight and can be carried by hand; installation is carried out from below, and the system helps to prevent musculoskeletal disorders. Only two people are needed to install it

How does the ALTRADAL system’s quick-release formwork work?

ALTRADAL incorporates a movable formwork head mounted on the props, which allows the panels to be stripped quickly. The equipment can therefore be reused more frequently from one area to another, which speeds up the formwork rotation cycle and reduces the amount of equipment required on site.

How many people does it take to install ALTRADAL slab formwork?

Only two people are needed to install the ALTRADAL slab formwork. The light weight of the aluminium beams and panels, combined with installation from below, simplifies the assembly process, reduces handling costs and improves safety for the teams during assembly.

What does Altrad’s ALTRADAL formwork system consist of?

ALTRADAL is a modular system comprising primary and secondary aluminium beams and panels that form the formwork support structure. Props are added at the base, topped with a formwork head. A dedicated storage basket is used to pack the equipment for storage and transport between sites.

Q&A - ALTRASTORE

What is the working load limit (WLL) for the ALTRASTORE materials package?

The ALTRASTORE material mix design from Altrad Coffrage & Etaiement has a load capacity of 3,000 kg centred, including personnel, equivalent to 450 kg/m² distributed. The site manager must, however, check the strength of the concrete slab and adjust the load capacity if necessary after installation.

Under what wind conditions can the ALTRASTORE system be used?

Loading is permitted at speeds of up to 85 km/h, provided that the loads are removed from the scaffolding within 5 minutes of loading. At speeds exceeding 85 km/h, no loading is permitted, and if winds exceeding 170 km/h are forecast, the scaffolding must be dismantled from the building.

Can the ALTRASTORE material rack be stacked for transport?

Yes. Once folded, the ALTRASTORE can be stacked up to four units high using dedicated storage racks, making it easier to transport by lorry and store in a warehouse.

Q&A - PROP KEY FLANGE

How do you secure a prop against a concrete wall without a tripod?

The Altrad Formwork & Shoring brace clamp is bolted onto the wall or column and secures the shoring leg, eliminating the need for a tripod at the edge of the formwork bay. It is positioned 15 cm below the shoring nut and can be fitted either before or after the shoring has been installed.

What prop diameters is the Altrad Formwork & Shoring prop clamp compatible with?

The dowel-type prop clamp is compatible with props with a shaft diameter of Ø57, Ø60 or Ø76 mm. It is therefore suitable for most construction props used for floor shoring. The brace is also compatible with any prop from the Altrad Formwork & Shoring range, as well as with props from other brands.

Can a prop clamp be used on a staircase?

Yes. The Altrad prop clamp is specifically designed to secure props on staircases, as well as against wall panels and posts. It ensures that props are securely positioned in areas where tripods are difficult to set up.

What is the purpose of a strut clamp on a structural works site?

The strut clamp reduces handling time by eliminating the need for tripods at the edge of the cell, frees up passageways thanks to its compact size, and offers flexible installation, either before or after the strut has been positioned. It weighs 1.8 kg and is available in a Galvanised or painted finish.

Q&A - Concrete mould block

How can you secure a formwork panel against the wind?

The Altrad Coffrage & Etaiement concrete block is usedas a base for formwork stabilisers, in particular JALFORM EVO formwork panels. Filled with concrete on site, it absorbs the wind loads transmitted by the stabilisers and accommodates various bracing fixings.

Is the Altrad Coffrage & Etaiement concrete block delivered full or empty?

It is delivered empty, which reduces transport costs. It is filled on site with standard concrete without reinforcement, with a minimum density of 2200 kg/m³, simply by placing the block on a level surface.

What is the advantage of a steel-cased concrete block over a block of plain concrete?

The concrete block is made from hot-dip galvanised S235 steel: it is corrosion-resistant, lasts longer than a cast-in-situ concrete ballast, and features lifting and anchoring points that ensure the safe use of a crane and the secure attachment of stabilisers.

Can the concrete block be lifted by a crane?

Yes. The Altrad concrete block incorporates lifting and anchoring points designed for crane lifting and handling on site. Once filled, it is moved by crane to keep pace with the progress of the formwork panels that need to be stabilised.

Q&A - ESCAPLUS

What height can the ESCAPLUS site staircase reach?

The ESCAPLUS system from Altrad Formwork & Shoring consists of standard modules with a working height of 2.40 m, which can be stacked up to 10 modules high. It therefore allows access heights of up to 24 metres, whilst maintaining a compact floor area of 1.50 m x 1.50 m between posts.

How many people can use ESCAPLUS at the same time?

The ESCAPLUS site staircase can accommodate up to 10 people, representing a load of 1,000 daN. Its steps can withstand a distributed load of 200 daN/m² and a concentrated load of 360 daN.

Does ESCAPLUS offer outings at different levels?

Yes. The ESCAPLUS from Altrad Coffrage & Etaiement allows for lateral access points every 60 cm on all four sides of the tower and can be rotated in 90° increments. This flexibility allows for precise access to floor levels, scaffolding or work platforms, regardless of the site layout – particularly in confined spaces – as the ESCAPLUS is easy to assemble and dismantle.

Which standard applies to a site staircase?

In France, construction site access towers with step ladders or staircases are governed by theNF P 93-521 standard. The ESCAPLUS construction site staircase from Altrad Coffrage & Étaiement complies with this standard, ensuring that staff can access workstations, scaffolding and shoring towers under verified safety conditions.

Q&A - GUARDRAILS

What is the purpose of a construction site guardrail?

A construction site guardrail is a collective protection system that prevents falls from height from the edges of slabs, openings or work areas exposed to a drop. Altrad Coffrage & Étaiement guardrails ensure safety on construction sites, with a wide range of products to suit all requirements.

What types of site guardrails does Altrad Coffrage & Etaiement offer?

The Altrad Coffrage & Scaffolding range includes smooth tubes, a roof protection system designed for detached house building sites, as well as extendable and fixed window guardrails to secure façade openings. These components can be combined with Altrad Coffrage & Scaffolding posts to form complete perimeter protection systems.

Why should collective protection be prioritised over PPE when it comes to fall protection?

Collective protection, such as site guardrails, provides constant protection for all workers, without relying on them to wear personal protective equipment. This is the preferred preventive approach in the construction industry. Altrad guardrails follow this approach by physically securing areas exposed to a drop.

Q&A- GEMAGRILLE

How can you secure a lift shaft on a building site?

The lift shaft must be sealed off at each level to prevent people and objects from falling. The Gémagrille from Altrad Coffrage & Étaiement is a dedicated temporary protection system: a galvanised steel grille that seals the opening throughout the structural work phase, until the lift is installed.

What sizes of Gemagrille are available?

The Gemagrille from Altrad Coffrage & Étaiement is available in three sizes to suit the dimensions of the hoppers: 400 mm (16 kg), 600 mm (19 kg) and 750 mm (21 kg). Each grid has ergonomic handles positioned at its centre of gravity, making handling it easier from one level to another on site.

Which standard applies to the protection of lift shafts?

The Gemagrille complies with standard NF EN 13374, Class A, the benchmark for temporary perimeter guardrails. It is also SUVA-approved in Switzerland and meets the requirements of occupational health insurance policies, which attests to the soundness of its design for the prevention of falls from height.

Is the Gemagrille eligible for financial support?

Yes. The Gemagrille is eligible for the TOP BTP grant, a support scheme designed to help construction companies purchase safety equipment. It also complies with the requirements of occupational health insurance policies, which is a further incentive for companies investing in safety.

Q&A - HD 320

What is the load capacity of the HD 320 shoring tower?

The HD 320 shoring tower from Altrad Coffrage & Étaiement offers a load capacity of up to 8 tonnes per foot. This high load capacity makes it ideal for demanding shoring applications: high-rise slabs, thick bridge decks and temporary shoring beneath concrete structures.

Can the HD 320 tower be erected without a safety harness?

Yes. The HD 320 shoring tower from Altrad Coffrage & Shoring has been designed for harness-free assembly using the MDS system (safe assembly and dismantling): its 1-metre frames incorporate an access ladder and a pin-and-wedge locking mechanism with automatic rotation lock, which ensures the safety of operators as they move between each level of the tower.

Is the HD 320 shoring tower compatible with other Altrad systems?

Yes. The HD 320 is compatible with the ALTRADAL slab formwork and the PLETTAC METRIX multi-directional scaffolding. This compatibility makes it possible to combine Étaiement, formwork and access on a single site using Altrad components that are fully compatible with one another.

Q&A - JALFORM EVO

What are the maximum wall heights that can be formworked using the JALFORM EVO?

The JALFORM EVO formwork system from Altrad Coffrage & Shoring is available in standard heights of 0.50 m, 1 m, 1.50 m and 2.80 m, which can be combined by stacking them on top of one another. This modular design allows the formwork to be adapted to the various wall heights encountered in both building and civil engineering projects. Contact our teams to find out more and obtain a bespoke quote.

What concrete pressure can the JALFORM EVO formwork panel withstand?

The JALFORM EVO formwork panel can withstand a concrete pressure of 10 t/m². It is suitable for both conventional reinforced concrete and self-compacting concrete, enabling concrete pouring at a sustained rate on the walls of buildings or civil engineering structures.

What safety features do the JALFORM EVO formwork panels include?

The JALFORM EVO comes with collective safety features as standard: guardrails, an access ladder and a composite floor with a hatch. Its safety components are electro-galvanised for durability, and the formwork panels’ wind stability is guaranteed up to 85 km/h.

Q&A - JALSEC

What is a cantilevered work platform?

A cantilevered platform is a piece of work equipment fixed to the edge of a structure, extending out at an angle, which provides workers with a safe working area from which to carry out structural work. The JALSEC platform from Altrad Coffrage & Étaiement fulfils this function on building and civil engineering sites, with a modular and foldable design.

What types of construction sites is the JALSEC platform suitable for?

The JALSEC system from Altrad Coffrage & Shoring can be adapted to any type of structure, from the smallest site to the most demanding: buildings, civil engineering works and concrete walls. Its modular design, achieved through sliding steel beams, a central bridge section and lateral extensions, enables it to adapt to a wide variety of structural geometries.

How is the JALSEC platform handled on a building site?

The JALSEC platform is handled by crane. This crane-accessible design allows the platform to be moved quickly from one phase of the works to the next, minimising assembly and dismantling operations, and therefore reducing downtime on site.

Does the JALSEC platform contribute to collective safety on the construction site?

Yes. JALSEC is a collective safety solution: it provides a protected workstation at the edge of the structure and helps to prevent falls from height for all workers, without relying solely on personal protective equipment.

Q&A - FORMWORK PANELS

What is the weight of an Altrad portable panel?

Altrad’s modular, hand-carried panels have a weight of approximately 21 kg/m². Some panels can be handled by hand whilst maintaining an excellent weight-to-performance ratio on site.

Is it possible to formwork a concrete wall without a crane?

Yes. Altrad Coffrage & Etaiement’s modular, manually handled panels have been specifically designed to form concrete walls without the need for motorised handling. Their light weight and modular design make it possible to construct concrete walls on confined building sites, during renovation work, or wherever crane access is impossible or too costly.

What standard of finish can be achieved with Altrad Coffrage & Etaiement’s portable formwork panels?

The formwork facing on Altrad’s portable panels is made from high-quality all-birch plywood, which ensures a high-quality finish on the concrete wall. This standard of facing is suitable for walls intended to remain exposed, as well as for standard building works.

Q&A - Basket storage

How many props can the Altrad Coffrage & Étaiement prop basket hold?

The prop basket, with a base measuring 120 x 90 cm and a height of 112 cm, can hold between 50 and 100 props, depending on the prop model. Its load capacity of 1.5 tonnes means it can be lifted by crane whilst loaded, using a 4-leg sling.

How do you safely lift a storage basket with a crane?

Altrad Coffrage & Shoring storage baskets are lifted using a 4-leg sling, with only one basket handled at a time. The slings must not be angled at less than 60° from the horizontal.

Are Altrad Coffrage & Shoring storage baskets available for hire?

Yes. The storage baskets are available for sale or hire, making them suitable for both one-off site requirements and for permanently equipping an equipment fleet. They are compatible with the entire range of Altrad formwork and Étaiement equipment.

Q&A - Posts

What is a post used for on a building site?

A post is a vertical support that holds up the rails of a temporary guardrail. Altrad Coffrage & Étaiement posts ensure the safety of site personnel against falls from height from a building or structure, by providing collective protection at the edge of a slab or around the perimeter of a floor.

What types of site posts does Altrad Coffrage & Etaiement supply?

The Altrad Coffrage & Etaiement range includes the multi-directional post with 2 or 3 locking mechanisms, the standard post, the slab clamp post, the reversible clamp post and the adjustable sliding post. This variety allows you to choose the right fastening for every type of support: concrete slab, floor edge or structural element.

How do you choose the right safety post to secure the edge of a slab?

The choice depends on the substrate and the desired fixing method: a slab-clamp safety post is fixed directly to the slab, whilst an adjustable sliding post or a post with a reversible clamp is suitable for other configurations. The Altrad Coffrage & Étaiement teams assist companies in selecting the appropriate model.

Q&A - Aluminium beam H10

What makes the H10 beam from Altrad Coffrage & Etaiement so special?

The H10 beam is as wide as it is high: once in place, it cannot tip over on its supports. This non-reversible design secures the formwork base decking and allows workers to move around during installation.

What span can an H10 beam achieve under a thick slab?

The H10 aluminium beam has a maximum span of 2 metres beneath a 60 cm-thick slab, with a spacing of 10 cm between beams. The dimensions must always be checked in accordance with the site configuration.

How much does the H10 aluminium beam weigh, and how long is it?

The Altrad Coffrage & Etaiement H10 aluminium beam weighs 11 kg and is 2.90 m long. Its light weight allows formwork teams to handle it easily by hand, without the need for lifting equipment, and speeds up the installation of formwork bases.

What are the advantages of an aluminium formwork beam compared to a wooden one?

The aluminium used in the H10 beam offers superior durability compared to timber: it does not absorb moisture or splinter, is resistant to repeated cycles of formwork erection and stripping, and can be reused on numerous building sites. Its light weight also makes it easier to handle on a day-to-day basis.

Q&A - Aluminium beam H16 EVO

What is the difference between the H16 EVO aluminium beam and an H20 wooden beam?

Altrad’s H16 EVO beam is based on the principle of using a wooden beam for the bottom of the formwork, but is made of aluminium: it is lighter than a timber beam, more durable over time and better suited to intensive reuse on numerous slab formwork sites.

What lengths are available for the H16 EVO aluminium beam?

The H16 EVO aluminium beam from Altrad Coffrage & Etaiement is available in 3 lengths: 240, 360 and 480 cm. This range covers all common applications in decking and formwork bases, from standard grids to compensation zones.

What are the mechanical performance characteristics of the H16 EVO beam?

The H16 EVO aluminium beam has a permissible bending moment (Md) of 6.10 kN·m, a permissible shear force (Vd) of 30 kN and a linear mass of 4 kg/m, making it a high-performance yet lightweight formwork beam.

Q&A - Aluminium beam H20

What are the mechanical characteristics of the H20 EVO beam?

The H20 EVO aluminium beam has a bending moment of 13.8 kN·m, a shear force of 36.3 kN and a reaction at the central support of 44 kN, with a linear mass of just 4.48 kg/m.

What lengths are available for the H20 EVO beam?

Altrad’s H20 EVO aluminium beam is available in a range of lengths, from 240 cm to 480 cm, and is also available in extra-long lengths of up to 6 m. This range is suitable for the most demanding long-span shoring configurations.

Is the H20 EVO beam easy to handle on site?

Yes. With a linear mass of 4.48 kg per metre, Altrad’s H20 EVO aluminium beam stands out for its ergonomic design: it is easy for teams to handle, which speeds up the assembly and dismantling of shoring systems for large spans.

Q&A - Aluminium beam H20 R-MAX

What is the H20 R-MAX beam from Altrad Coffrage & Etaiement?

The H20 R-MAX beam from Altrad Coffrage & Shoring is marketed as the first aluminium beam designed to transfer heavy loads in shoring applications. It is used, in particular, at the top of a shoring tower and as a primary beam for formwork.

What load can the H20 R-MAX beam at the top of the shoring tower ?

The H20 R-MAX beam can be used at the top of a shoring tower with support reactions of up to 8 tonnes per foot. The precise sizing must always be validated by a design study tailored to the site’s configuration. It is the ideal beam for use with the HD 320 shoring tower on civil engineering sites with more technical requirements.

What is the H20 R-MAX beam made of?

Altrad’s H20 R-MAX beam features rails on both flanges, allowing clamps to be secured using hammer-head bolts. Its galvanised metal end caps are fixed using the Alvéovis system, ensuring a quick and secure connection with the rest of the system.

Q&A - Facade retention

Which Altrad Coffrage & Shoring systems are used for façade shoring?

Altrad Coffrage & Etaiement relies on systems such as the Slimshor and the Megashor, which can be adapted to the environmental conditions of each site. The range includes lightweight, portable aluminium props as well as sturdy steel towers and trusses, depending on the specific requirements of the construction site.

For which refurbishment projects is façade retention suitable?

Altrad’s façade shoring solutions are designed for refurbishment projects where the building envelope is retained: listed façades, town centre regeneration projects and complete internal demolition works. The Slimshor and Megashor systems, supplemented by aluminium props or steel towers and trusses, cover the most common façade shoring configurations.

Q&A - Support of wooden beam

How can you formwork a corridor floor without cluttering the floor with props?

The Altrad support of wooden beam is attached to the formwork walls and directly supports the beams that bear the floor formwork. The floor remains completely clear during the formwork phase, which makes it easier to move around in corridors and narrow rooms.

What is the maximum load capacity of the Altrad support of wooden beam?

The maximum permissible load for the support of wooden beams on the corridor formwork shoe is 17.5 kN. It is designed to support beams as part of floor shoring in confined spaces, and is compatible with Altrad formwork equipment.

Is the support of wooden beam available in a version that can be fixed with dowels?

Yes. Altrad Coffrage & Shoring offers three models: a version with a 330 mm rod, a version with a 660 mm rod, and a version without a rod, designed to be anchored directly into the concrete wall depending on the site configuration.

How does the support of wooden beam improve handling efficiency?

The support of wooden beam reduces the weight of the loads being handled by around 80 per cent compared with traditional shoring, whilst allowing for rapid installation and formwork removal. This improves productivity and safety for the teams.

Q&A - PLYWOOD

Which type of plywood should you choose for concrete formwork?

Altrad Coffrage & Etaiement offers two ranges of formwork plywood: STARPLY, which is economical and versatile, ideal for standard and temporary applications, and XTRAPLY, which is more robust and durable, designed for intensive and repeated use. The choice depends on the intended number of reuses and the site’s finish requirements.

What is the difference between Altrad’s STARPLY and XTRAPLY plywood?

STARPLY is a cost-effective, fully kiln-dried timber plywood designed for general-purpose applications. XTRAPLY, made from eucalyptus, is more robust and durable, and is suitable for intensive and repeated use. Both ranges are 15 mm thick, measure 1220 x 2440 mm and feature a phenolic film on both sides.

Q&A - EASY UP

What is the advantage of an aluminium prop such as the EASY UP compared to a steel prop?

The EASY UP aluminium prop is lighter than traditional heavy-duty props. Its moderate weight makes it easier to handle on site, speeds up assembly and reduces physical strain, whilst retaining the robustness and impact resistance required for heavy-duty shoring.

How do you adjust the height of the EASY UP prop?

The EASY UP from Altrad Coffrage & Etaiement has a fully threaded sleeve and a nut that can be freely adjusted around the shaft. This system allows for precise and gradual adjustment of the prop height, suited to the various load-bearing configurations encountered on site.

Can accessories be fitted to the EASY UP prop?

Yes. The end plates of the EASY UP prop are fitted with various holes designed for assembly with a range of accessories, such as connecting frames. This design allows the prop to be adapted to a wide range of shoring configurations, depending on the requirements of the site.

Q&A - STRAIGHT PROPS & PUSH PULL (Rental)

Which Push-pull prop should I hire for a high-rise wall?

For work at great heights, Altrad Coffrage & Étaiement offers the TP 1000, a high-rise Push-pull prop, for hire. For heavy loads, the RAS TP range is ideal. Altrad’s technical team will help you select the right solution for your project.

Where can I hire scaffolding props in France?

Altrad Coffrage & Étaiement offers straight props and push-pull props for hire throughout France. The hire fleet comprises the SE, SE C4 and RAS ranges for straight props, and the TPE, RAS TP and TP 1000 ranges for push-pull props, all available at short notice.

Why rent your props rather than buy them?

Hiring props from Altrad Coffrage & Étaiement allows you to equip a one-off construction site without tying up capital, to cope with peaks in activity, and to have access to equipment that is compliant and inspected. For recurring requirements, Altrad also offers straight props and public works props for sale.

Q&A - STRAIGHT PROPS & PUSH PULL (Sales)

Where can I buy new, compliant construction props?

Altrad Coffrage & Étaiement sells new straight props and push-pull props that comply with industry standards. The range includes SE, SN, RAS and Euronorme Class D and E straight props, as well as TPE, RAS TP, TPSS and TP 1000 push-pull props. Request a quote at altrad-coffrage.com.

How much does a construction prop cost?

The price of a prop depends on its range, load capacity and the quantities ordered. At Altrad Coffrage & Étaiement, the SN range offers the best value for money, whilst the SE and RAS ranges are designed for intensive use and heavy loads. A personalised quote is provided on request.

What is a Class D or E Euronorm prop?

Euronorme props are classified in accordance with the European standard for telescopic props, with the class defining their load-bearing capacity. Altrad Coffrage & Étaiement offers Euronorme props in classes D and E for sale; its technical team can advise you on the appropriate class for your loads.

Q&A - MAC BLOQUEUR

How can you ensure safety during masonry work on a façade without leaning on the walls?

The MAC BLOQUEUR uses rigid, self-supporting masts anchored to the concrete slab, without any support from the masonry. No anchoring is carried out in brittle or hollow materials, which ensures reliable protection of the upper level during hoisting.

Does the MAC BLOQUEUR comply with any fall protection standards?

Yes. The MAC BLOQUEUR from Altrad Coffrage & Étaiement complies with the NF EN 13374 Class A standard, the European standard for temporary perimeter guardrails. It ensures complete safety on the upper level during façade masonry work.

For which types of construction sites is the MAC BLOQUEUR intended?

The MAC BLOQUEUR is designed for construction sites involving both concrete and masonry: block-of-flats, commercial buildings and high-rise buildings. It protects the masonry work on the façade by anchoring itself to the concrete slabs.

Q&A - MAX UP

What is the advantage of an aluminium prop such as the MAX UP compared to the EASY UP?

The MAX UP aluminium prop is similar to theEASY UP. The difference lies in the prop’s load-bearing capacity. This is superior with the MAX UP. Furthermore, the MAX UP features removable and interchangeable end plates to ensure the prop’s longevity and facilitate their maintenance. It takes just a few seconds to give your prop a new lease of life. Furthermore, the MAX UP is made from a higher-grade aluminium: AL6005 T6.

How do you adjust the height of the MAX UP strut?

The MAX UP from Altrad Coffrage & Étaiement features a fully threaded sleeve and a nut that can be freely adjusted around the shaft. A graduated scale is integrated into the sleeve, indicating the total length of the prop. This system allows for precise and gradual adjustment of the height of the shoring, adapting to the various load-bearing configurations encountered on site.

Q&A - Basket storage

How many props can the Altrad Coffrage & Étaiement prop basket hold?

The prop basket, with a base measuring 120 x 90 cm and a height of 112 cm, can hold between 50 and 100 props, depending on the prop model. Its load capacity of 1.5 tonnes means it can be lifted by crane whilst loaded, using a 4-leg sling.

How do you safely lift a storage basket with a crane?

Altrad Coffrage & Shoring storage baskets are lifted using a 4-leg sling, with only one basket handled at a time. The slings must not be angled at less than 60° from the horizontal.

Are Altrad Coffrage & Shoring storage baskets available for hire?

Yes. The storage baskets are available for sale or hire, making them suitable for both one-off site requirements and for permanently equipping an equipment fleet. They are compatible with the entire range of Altrad formwork and Étaiement equipment.

Q&A - FORMWORK PANELS

What is the weight of an Altrad portable panel?

Altrad’s modular, hand-carried panels have a weight of approximately 21 kg/m². Some panels can be handled by hand whilst maintaining an excellent weight-to-performance ratio on site.

Is it possible to formwork a concrete wall without a crane?

Yes. Altrad Coffrage & Etaiement’s modular, manually handled panels have been specifically designed to form concrete walls without the need for motorised handling. Their light weight and modular design make it possible to construct concrete walls on confined building sites, during renovation work, or wherever crane access is impossible or too costly.

What standard of finish can be achieved with Altrad Coffrage & Etaiement’s portable formwork panels?

The formwork facing on Altrad’s portable panels is made from high-quality all-birch plywood, which ensures a high-quality finish on the concrete wall. This standard of facing is suitable for walls intended to remain exposed, as well as for standard building works.

Q&A - Wall bracket anchor rod

How do you prop up a beam when you cannot erect a shoring tower?

The Altrad Coffrage & Etaiement wall bracket anchor rod is designed for this purpose: secured to the concrete wall by a Ø24 mm through-rod, it transfers the shoring loads directly to the wall, with a load capacity of 4 tonnes, without taking up any floor space.

What load can the wall bracket anchor rod support?

The Altrad Coffrage & Étaiement wall bracket anchor rod has a load capacity of 4 tonnes. It weighs 8.5 kg and is secured using a Ø24 mm rod, the length of which corresponds to the thickness of the wall plus 100 mm.

Which shoring systems is the rod-mounted shoe compatible with?

The wall bracket anchor rod is compatible with the STAFLEX shoring towers from the Altrad range. This specific compatibility ensures consistency throughout the shoring system, from the wall anchor to the load-bearing structure.

What is the advantage of a wall-shoring prop on a building site?

By transferring the shoring loads onto the concrete wall, the Altrad wall bracket anchor rod frees up corridors and walkways at ground level and secures the supports for beams and floor slabs on tall walls, where a shoring tower would be cumbersome or impossible to install.

Q&A - Wall bracket anchor plate

What is the difference between a wall bracket anchor rod and a wall bracket anchor plate?

The through-bolt anchor is secured using a through-bolt and has a load capacity of 4 tonnes, whilst the anchor bolt is secured from a single side of the wall and has a load capacity of 6 tonnes. The choice depends on the accessibility of the wall and the load to be supported.

What load can the Altrad wall bracket anchor plate?

The Altrad Coffrage & Étaiement wall bracket anchor plate has a load capacity of 6 tonnes. It is Galvanised, weighs 15 kg and measures 250 x 270 x 215 mm; it is secured to the concrete wall using anchor screws.

How can you ensure that a floor is securely supported by a wall of high height?

The Altrad wall bracket anchor plate is anchored directly into the concrete wall and provides support for beams and floor slabs during the shoring phase. It secures the supports on tall walls whilst keeping the aisles clear, without the need for ground-level shoring towers.

Q&A - SECUTABLE EVO

Can you remove the formwork from a balcony whilst leaving the props in place?

Yes. Altrad’s SECUTABLE EVO formwork features a prop locking mechanism using a wedge via the prop head: when the formwork is removed, the props remain in place to allow the concrete to cure beneath the slab. The concrete continues to cure whilst the formwork is reused on the next section.

Is the SECUTABLE EVO formwork table compatible with all props?

Yes, the SECUTABLE EVO formwork table is compatible with all types of props. This compatibility allows structural contractors to use it with their existing shoring stock, without the need for additional investment in system-specific props.

What is the SECUTABLE EVO formwork table made of?

Altrad’s SECUTABLE EVO combines IPN140 steel primary beams with H20 wooden beams. The steel primary beams are pre-drilled to allow for cantilevers, and anchoring brackets secure the formwork to the lintel or wall during concreting.

Q&A - SL 40

What load can the SL 40 prop support?

The SL 40 prop from Altrad Coffrage & Étaiement is designed to support loads of 40 tonnes. When used vertically, combining several SL 40 props allows the load capacity to be increased, enabling even heavier loads to be supported.

The SL 40 is particularly recommended for shoring civil engineering structures, stabilising facades and propping. Its modular design allows it to be used as vertical, horizontal or inclined support, depending on the requirements of the site.

How do you brace an SL 40 shoring?

The bracing and cross-bracing of Altrad’s SL 40 props are carried out using standard scaffolding tubes. This compatibility with standard site equipment simplifies installation and reduces the number of specialist components that need to be sourced.

Q&A- SLIMSHOR

What are the dimensions of SLIMSHOR beams?

The beams in Altrad Coffrage & Etaiement’s SLIMSHOR system weigh 21 kg and are available in lengths ranging from 90 mm to 3,600 mm. Their design allows anchors and fixings to be positioned along their entire length, enabling them to adapt to any site configuration.

Can SLIMSHOR be used for façade retention during renovation work?

Yes. Supporting façades during renovation is one of the main applications of Altrad’s SLIMSHOR. Its modularity and high load-bearing capacity enable preserved façades to be supported whilst demolition or reconstruction work is carried out behind them.

How are the SLIMSHOR elements assembled?

SLIMSHOR beams are assembled using single or double 6-sided connectors. This system allows for the construction of straight or inclined props, telescopic beams, frames or span beams, for use in a vertical, inclined or horizontal orientation.

Q&A - STAFLEX MULTIDYNAMIC

What is the difference between aluminium and steel frames on the Staflex Multidynamic?

The frames of the Staflex Multidynamic tower are available in aluminium or steel. Aluminium offers the advantages of lightness and ease of handling, whilst steel is chosen for its strength. The choice depends on the load, handling and organisational requirements specific to each site.

Can Staflex Multidynamic be used to key a beam?

Yes. The AMOVICLAV system, available with the Staflex Multidynamic tower from Altrad Coffrage & Étaiement, provides protection at the top of the shoring tower. It is used in particular to ensure safety during operations at the top of the tower, such as the wedging of concrete beams.

Q&A - STAFLEX NT24

What load can the Staflex NT24 shoring tower support?

The Staflex NT24 shoring tower offers a capacity of up to6 tonnes per foot in the steel version, and up to 5 tonnes per foot in the aluminium version. These capacities make it suitable for shoring slab formwork in both the building and civil engineering sectors.

How is the Staflex NT24 shoring tower moved around on site?

The Staflex NT24 tower is crane-liftable and can be moved by rolling using a rack-and-pinion trolley or wheeled jacks. These methods of movement allow the towers to be rotated from one formwork plinth to another without having to be completely dismantled, which speeds up production cycles.

For which construction projects is the Staflex NT24 tower suitable?

The Staflex NT24 from Altrad Coffrage & Étaiement is designed for shoring slab formwork on all types of construction sites: building and civil engineering. Available in steel or aluminium and with a range of movement options (crane lifting, sliding), it is suitable for both standard floor slabs and more demanding structures.

Q&A- TETRASHOR

What is the maximum height a TETRASHOR shoring system can reach?

The TETRASHOR system from Altrad Coffrage & Étaiement enables the erection of individual accessories up to 17 m and interlaced towers up to 22 m in height. This capability makes it a suitable solution for engineering structures and high-rise shoring.

What load can the TETRASHOR support?

Altrad’s TETRASHOR offers a maximum working load of 400 kN. Its tilting plate can withstand 200 kN at any angle when operated by a hydraulic cylinder, and 400 kN at angles of up to 15°, enabling it to support inclined loads as well.

Is TETRASHOR compatible with other shoring systems?

Yes. The TETRASHOR is compatible with the MEGASHOR and SLIMSHOR systems from Altrad Coffrage & Étaiement. This compatibility makes it possible to create hybrid shoring solutions suited to complex structures, by combining the strengths of each system.

Q&A - Forks & lifting beams

How do you move a formwork table from one floor to another?

Altrad Coffrage & Etaiement offers two lifting accessories: the 550 kg lifting fork and the 250/540 lifting beam (load capacity 1 tonne). When attached to the crane, they grip the formwork panel and lift it to the next level without the need for dismantling, thereby speeding up the rotation of the formwork equipment.

What is the lifting capacity of the forklift?

The Altrad lifting fork has a working load limit (WLL) of 550 kg and a kerb weight of 410 kg. It can be adjusted to suit the lengths of the formwork panels to be handled and is compatible with the SECUTABLE EVO panel.

Are Altrad forks and lifting beams compatible with the SECUTABLE EVO?

Yes. The 550 kg lifting fork and the 250/540 lifting beam from Altrad Coffrage & Étaiement are both compatible with the SECUTABLE EVO formwork panel, forming a complete formwork and formwork panel handling system.